diff --git a/include/configs/XPEDITE1K.h b/include/configs/XPEDITE1K.h
index d533b17..569bb90 100644
--- a/include/configs/XPEDITE1K.h
+++ b/include/configs/XPEDITE1K.h
@@ -38,29 +38,29 @@
 #define CONFIG_440		1
 #define CONFIG_440GX		1		/* 440 GX */
 #define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_pre_init	*/
-#undef	CFG_DRAM_TEST				/* Disable-takes long time! */
+#undef	CONFIG_SYS_DRAM_TEST				/* Disable-takes long time! */
 #define CONFIG_SYS_CLK_FREQ	33333333	/* external freq to pll */
 
 
 /* POST support */
-#define CONFIG_POST		(CFG_POST_RTC	   | \
-				 CFG_POST_I2C)
+#define CONFIG_POST		(CONFIG_SYS_POST_RTC	   | \
+				 CONFIG_SYS_POST_I2C)
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE	    0x00000000		/* _must_ be 0		*/
-#define CFG_FLASH_BASE	    0xfff80000		/* start of FLASH	*/
+#define CONFIG_SYS_SDRAM_BASE	    0x00000000		/* _must_ be 0		*/
+#define CONFIG_SYS_FLASH_BASE	    0xfff80000		/* start of FLASH	*/
 
-#define CFG_MONITOR_BASE    CFG_FLASH_BASE	/* start of monitor	*/
-#define CFG_PCI_MEMBASE	    0x80000000		/* mapped pci memory	*/
-#define CFG_PERIPHERAL_BASE 0xe0000000		/* internal peripherals */
-#define CFG_ISRAM_BASE	    0xc0000000		/* internal SRAM	*/
-#define CFG_PCI_BASE	    0xd0000000		/* internal PCI regs	*/
+#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_FLASH_BASE	/* start of monitor	*/
+#define CONFIG_SYS_PCI_MEMBASE	    0x80000000		/* mapped pci memory	*/
+#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000		/* internal peripherals */
+#define CONFIG_SYS_ISRAM_BASE	    0xc0000000		/* internal SRAM	*/
+#define CONFIG_SYS_PCI_BASE	    0xd0000000		/* internal PCI regs	*/
 
-#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000)
-#define CFG_GPIO_BASE	    (CFG_PERIPHERAL_BASE + 0x00000700)
+#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
+#define CONFIG_SYS_GPIO_BASE	    (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
 
 #define USR_LED0	    0x00000080
 #define USR_LED1	    0x00000100
@@ -71,33 +71,33 @@
 extern unsigned long in32(unsigned int);
 extern void out32(unsigned int, unsigned long);
 
-#define LED0_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED0))
-#define LED1_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED1))
-#define LED2_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED2))
-#define LED3_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED3))
+#define LED0_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED0))
+#define LED1_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED1))
+#define LED2_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED2))
+#define LED3_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED3))
 
-#define LED0_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED0))
-#define LED1_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED1))
-#define LED2_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED2))
-#define LED3_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED3))
+#define LED0_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED0))
+#define LED1_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED1))
+#define LED2_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED2))
+#define LED3_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED3))
 #endif
 
 /*-----------------------------------------------------------------------
  * Initial RAM & stack pointer (placed in internal SRAM)
  *----------------------------------------------------------------------*/
-#define CFG_TEMP_STACK_OCM  1
-#define CFG_OCM_DATA_ADDR   CFG_ISRAM_BASE
-#define CFG_INIT_RAM_ADDR   CFG_ISRAM_BASE  /* Initial RAM address	*/
-#define CFG_INIT_RAM_END    0x2000	    /* End of used area in RAM	*/
-#define CFG_GBL_DATA_SIZE   128		    /* num bytes initial data	*/
+#define CONFIG_SYS_TEMP_STACK_OCM  1
+#define CONFIG_SYS_OCM_DATA_ADDR   CONFIG_SYS_ISRAM_BASE
+#define CONFIG_SYS_INIT_RAM_ADDR   CONFIG_SYS_ISRAM_BASE  /* Initial RAM address	*/
+#define CONFIG_SYS_INIT_RAM_END    0x2000	    /* End of used area in RAM	*/
+#define CONFIG_SYS_GBL_DATA_SIZE   128		    /* num bytes initial data	*/
 
 
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_POST_WORD_ADDR  (CFG_GBL_DATA_OFFSET - 0x4)
-#define CFG_INIT_SP_OFFSET  CFG_POST_WORD_ADDR
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_POST_WORD_ADDR  (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
+#define CONFIG_SYS_INIT_SP_OFFSET  CONFIG_SYS_POST_WORD_ADDR
 
-#define CFG_MONITOR_LEN	    (256 * 1024)    /* Reserve 256 kB for Mon	*/
-#define CFG_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
+#define CONFIG_SYS_MONITOR_LEN	    (256 * 1024)    /* Reserve 256 kB for Mon	*/
+#define CONFIG_SYS_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
 
 /*-----------------------------------------------------------------------
  * Serial Port
@@ -105,7 +105,7 @@
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_BAUDRATE		9600
 
-#define CFG_BAUDRATE_TABLE  \
+#define CONFIG_SYS_BAUDRATE_TABLE  \
     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
 
 /*-----------------------------------------------------------------------
@@ -115,23 +115,23 @@
  * The DS1743 code assumes this condition (i.e. -- it assumes the base
  * address for the RTC registers is:
  *
- *	CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE
+ *	CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_SIZE
  *
  *----------------------------------------------------------------------*/
 /* TBS:	 Xpedite 1000 has STMicro M41T00 via IIC */
 #define CONFIG_RTC_M41T11 1
-#define CFG_I2C_RTC_ADDR 0x68
-#define CFG_M41T11_BASE_YEAR 2000
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR 2000
 
 /*-----------------------------------------------------------------------
  * FLASH related
  *----------------------------------------------------------------------*/
-#define CFG_MAX_FLASH_BANKS	1		    /* number of banks	    */
-#define CFG_MAX_FLASH_SECT	8		    /* sectors per device   */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1		    /* number of banks	    */
+#define CONFIG_SYS_MAX_FLASH_SECT	8		    /* sectors per device   */
 
-#undef	CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	    /* Timeout for Flash Write (in ms)	*/
+#undef	CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	    /* Timeout for Flash Write (in ms)	*/
 
 /*-----------------------------------------------------------------------
  * DDR SDRAM
@@ -144,9 +144,9 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C			    /* I2C bit-banged		*/
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7f
-#define CFG_I2C_NOPROBES	{0x55,0x56,0x57,0x58,0x59,0x5a,0x5b,0x5c,0x69}	/* Don't probe these addrs */
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_SLAVE		0x7f
+#define CONFIG_SYS_I2C_NOPROBES	{0x55,0x56,0x57,0x58,0x59,0x5a,0x5b,0x5c,0x69}	/* Don't probe these addrs */
 
 /*-----------------------------------------------------------------------
  * Environment
@@ -154,10 +154,10 @@
 #define CONFIG_ENV_IS_IN_EEPROM 1
 #define CONFIG_ENV_SIZE		0x100	    /* Size of Environment vars */
 #define CONFIG_ENV_OFFSET		0x100
-#define CFG_I2C_EEPROM_ADDR	0x50		/* this is actually the second page of the eeprom */
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* this is actually the second page of the eeprom */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
 
 #define CONFIG_BOOTARGS		"root=/dev/hda1 "
 #define CONFIG_BOOTCOMMAND	"bootm ffc00000"    /* autoboot command */
@@ -165,7 +165,7 @@
 #define CONFIG_BAUDRATE		9600
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII			1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address phy0 not populated */
@@ -175,7 +175,7 @@
 #define CONFIG_NET_MULTI	1
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 #define CONFIG_PHY_RESET        1       /* reset phy upon startup         */
-#define CFG_RX_ETH_BUFFER   32	/* Number of ethernet rx buffers & descriptors */
+#define CONFIG_SYS_RX_ETH_BUFFER   32	/* Number of ethernet rx buffers & descriptors */
 
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
 #define CONFIG_HAS_ETH2		1	/* add support for "eth2addr"	*/
@@ -214,24 +214,24 @@
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
+#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
 
-#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 
 /*-----------------------------------------------------------------------
@@ -242,20 +242,20 @@
 #define CONFIG_PCI				    /* include pci support		*/
 #define CONFIG_PCI_PNP				/* do pci plug-and-play		*/
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/
-#define CFG_PCI_TARGBASE    0x80000000	/* PCIaddr mapped to CFG_PCI_MEMBASE */
+#define CONFIG_SYS_PCI_TARGBASE    0x80000000	/* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
 
 /* Board-specific PCI */
-#define CFG_PCI_TARGET_INIT		    /* let board init pci target    */
+#define CONFIG_SYS_PCI_TARGET_INIT		    /* let board init pci target    */
 
-#define CFG_PCI_SUBSYS_VENDORID 0x1014	/* IBM */
-#define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
-#define CFG_PCI_FORCE_PCI_CONV          /* Force PCI Conventional Mode */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014	/* IBM */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
+#define CONFIG_SYS_PCI_FORCE_PCI_CONV          /* Force PCI Conventional Mode */
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*
  * Internal Definitions